Home/Services/Dryer Repair
Dryer repair

Dryer Repair in Visalia, CA

We repair gas and electric dryers that won’t heat, take two cycles to dry, squeal or shut off mid-cycle, in homes across Visalia and nearby Tulare County towns. Every visit includes an airflow check, because a blocked vent sits behind many no-heat and slow-drying calls.

4.8 on Google
BHGS registered
Gas & electric
90-day warranty
Dryer running hot?

Talk to a technician, 24/7

  • Overheating dryers go to the front of the line
  • $49 diagnostic, written quote first
  • 90-day parts & labor warranty

Need dryer repair in Visalia? Call (559) 597-1018 and tell us whether your dryer runs on gas or electric and what it’s doing. A technician comes out, often the same day, tests the heat circuit and the vent airflow, and quotes the fix in writing. Our trucks carry thermal fuses, heating elements, igniters, gas valve coils, belts and rollers, so most dryers run again on the first visit. Every repair carries a 90-day parts and labor warranty.

Fix the cause

Visalia Dryer Repair That Fixes the Cause, Not Just the Part

Most dryer calls start the same way: clothes come out damp after a full cycle, or the drum spins but the air stays cold.

Often a part has failed. Just as often, a lint-choked vent made the dryer overheat and burned out that part. Replace the fuse without clearing the vent and you’ll call again next month.

That’s why we check airflow at the vent on every dryer call, gas or electric, before we quote.

What Our Dryer Repair Covers

  • Electric dryers: heating elements, thermal fuses, cycling and high-limit thermostats, terminal blocks and power cords
  • Gas dryers: igniters, flame sensors, gas valve solenoid coils, burner assemblies
  • Both: drive belts, drum rollers, idler pulleys, drum glides and bearings
  • Door switches, start switches, timers, moisture sensors and control boards
  • Motors and blower wheels
  • Airflow testing and lint removal from the dryer cabinet and transition duct
  • If the wall or roof vent needs a full cleaning, we’ll tell you what we measured and who to call
Local know-how

Why Dryers Struggle in Visalia

Tule fog season means more dryer hours

From roughly November through March, damp, foggy days mean fewer loads go on the line and more go in the dryer. The U.S. Fire Administration found that residential dryer fires run higher in fall and winter and peak in January, and that failure to clean was the leading factor.

Valley dust and lint

Dust from fields and roads joins the lint in vents and on the blower wheel. A vent that clogs faster than you’d expect usually explains a dryer that’s running hot.

Long vent runs in newer homes

A laundry room that doesn’t sit on an outside wall vents through a longer run with more bends, and every bend slows the air. We see this in plenty of newer Visalia homes.

Gas dryers are everywhere

SoCalGas supplies utility gas in Visalia, and gas is the most common home-heating fuel here, so many laundry rooms have a gas hookup. Some rural homes run dryers on propane, which needs the right burner orifice; a dryer converted the wrong way burns poorly.

Hot garages

Dryers in a garage pull in summer air well over 100°F. They still dry, but the thermostats and fuses work closer to their limits.

Symptoms & fixes

Dryer Problems We Fix Across Visalia

Find the symptom that matches yours. Gas and electric dryers share most mechanical parts but heat differently, so we split the no-heat problem by type.

Electric Dryer Not Heating

What we usually find
A blown thermal fuse, a burned-out heating element, a failed cycling or high-limit thermostat, or only one of the two breaker legs feeding the dryer.
Check this first
Electric dryers run on a 240-volt double breaker. If one half trips, the drum still turns but the heat stops. Flip that breaker fully off, then on. Then check the vent.
The repair
Fuses, elements and thermostats are usually same-visit fixes. A blown thermal fuse almost always means the dryer overheated, so we find out why before we leave.

Gas Dryer Not Heating

What we usually find
A weak igniter, a failed flame sensor, worn gas valve coils, a blown thermal fuse, or a closed gas valve after other work in the house.
Check this first
Make sure the gas shutoff valve behind the dryer is open (handle in line with the pipe). If you smell gas at any point, stop and follow the safety steps below.
The repair
If the igniter glows but the flame never lights, or lights and drops out, the valve coils are the usual cause. Coils and igniters are common, inexpensive parts.

Dryer Takes Too Long to Dry

What we usually find
A restricted vent, a clogged lint screen housing, a crushed transition hose behind the dryer, a blocked outside vent flap, a weak heat source, or a washer that isn’t spinning the water out.
Check this first
Run the dryer and go outside to the vent hood. You should feel a strong, warm blast. A weak puff means the vent needs cleaning. Also wash the lint screen with soap and water if it looks waxy from dryer sheets.
The repair
We clear the dryer’s internal lint path and transition duct and test the heat circuit. If clothes come out of the washer dripping, see our washer repair page.

Dryer Won’t Start or Won’t Tumble

Motor hums but the drum doesn’t turn
A broken belt or a seized roller or idler pulley.
Nothing at all
A door switch, start switch, thermal fuse (on many models it cuts the motor too), or a power problem.
Check this first
Confirm the door latches fully and the breaker is on. If the drum spins freely by hand with no resistance, the belt has likely snapped.
The repair
Belts, rollers and switches are on the truck and usually finish in one visit.

Squealing, Thumping or Scraping

Squeal or chirp
Worn idler pulley or drum rollers.
Rhythmic thump
Flat spots on rollers or a worn belt.
Scraping
Worn drum glides or felt seals, or a coin or bra wire caught between the drum and the cabinet.
The repair
We usually replace rollers, pulley and belt together; they wear as a set, and doing them at once saves a second labor charge.

Dryer Shuts Off Mid-Cycle or Gets Too Hot

What we usually find
A restricted vent tripping the high-limit thermostat, a failing cycling thermostat, an overheating motor, or a moisture-sensor or control fault.
Check this first
Clean the lint screen and check airflow at the outside vent. If the top of the dryer feels hot to the touch, stop using it until we check it.
The repair
We clear the airflow problem and replace the failed thermostat or sensor. A dryer that overheats is a fire risk, so this one doesn’t wait.

Burning Smell

New dryer or new heating element
A light burning smell for the first few loads is normal.
Any other time
Lint burning on the element or burner, or a motor or wire overheating. Stop the dryer, unplug it or switch off its breaker, and call us.
Safety first

Smell Gas or Burning? What to Do Right Now

If the dryer is just running hot: clean the lint screen, pull the dryer out a few inches, and check that the hose behind it isn’t crushed. Don’t leave it running while you’re out or asleep until we’ve looked at it.

If you smell gas near the dryer

  1. Don’t turn the dryer, lights or any switch on or off, and don’t use a phone near the smell.
  2. Get everyone out of the house.
  3. From outside, call SoCalGas’s emergency line or 911.
  4. Call us once the gas utility has made it safe. We’ll repair the dryer and leak-check every connection we touch.

If you smell burning or see smoke

  1. Stop the dryer and leave the door closed.
  2. Unplug it or switch off its breaker if you can do so safely. For a gas dryer, also close the gas valve behind it.
  3. If there’s smoke or flame, get out and call 911.
  4. Don’t run the dryer again until it’s been checked.
Vent safety

Dryer Vent Safety for Visalia Homes

The U.S. Fire Administration estimates about 2,900 residential dryer fires a year in the U.S., and names failure to clean as the leading factor behind them. Lint is fuel, and a restricted vent traps heat around it. A few checks keep you safe.

Clean the lint screen every load

Wash it with soap and water every few months if dryer sheets leave a film.

Check the hose behind the dryer

Dryer manufacturers specify rigid or UL-listed flexible metal duct. Plastic or vinyl hose is not approved, and thin foil hose crushes and traps lint. If yours is white plastic, replace it.

Feel the airflow outside

A strong, warm blast at the outside hood means the vent is clear. A weak flow, or a flap that doesn’t open, means it’s time to clean the vent.

Watch for warning signs

Loads taking two cycles, a hot dryer top, a laundry room that feels humid, or lint around the outside hood.

Dryer Error Codes We See Most

BrandCode or lightWhat it meansWhat to do
LGFlow Sense bars, d80About 80% exhaust restrictionClean the lint screen and vent soon
LGd90About 90% restrictionStop and clean the vent before the next load
LGd95About 95% restriction; severeDon’t run the dryer until the vent is cleared
Any brand“Check Vent” or airflow lightThe dryer detects poor exhaust flowCheck the transition hose and outside hood

LG’s own support pages say Flow Sense codes point to poor venting and that the dryer may shut down to prevent overheating. If the code returns right after a vent cleaning, a thermostat or sensor may be at fault, and that’s a service call. Codes vary by model, so check your manual.

Types & brands

Dryer Types and Brands We Repair in Visalia

Dryer typeHow it heatsWhat tends to fail
Electric240-volt heating elementThermal fuses, elements, thermostats, terminal blocks
Gas (natural gas)Burner lit by a hot-surface igniterIgniters, flame sensors, gas valve coils, thermal fuses
Gas (propane)Same burner with a propane orificeSame parts, plus orifice and setup problems after a conversion
Stacked laundry center or washer towerElectric or gasSame parts, with tighter access

Brands We Service

  • Whirlpool
  • Maytag
  • Amana
  • Kenmore
  • Samsung
  • LG
  • GE
  • Frigidaire
  • Electrolux
  • Bosch
  • Haier
  • KitchenAid

From the bench

  • Whirlpool, Maytag, Amana and many Kenmore dryers share a common design family, so belts, rollers, fuses and thermostats for them are easy to source.
  • Gas dryers: an igniter that glows but never lights the flame usually points to the gas valve coils, not the igniter.
  • LG dryers with Flow Sense tell you when the vent is clogging. Treat those bars as an early warning, not an annoyance.
See all brands we service
How it works

How Our Visalia Dryer Repair Works

1

Call or book online

Tell us gas or electric, the brand, and what it’s doing. Have the model tag handy; it’s usually inside the door opening or on the back.

2

We confirm your arrival

We call to confirm your appointment time, and call ahead if anything changes.

3

We diagnose, check airflow and quote

We test the heat circuit with a meter, check the belt and rollers, and measure airflow at the vent. You get a written price for the repair, plus a note on the vent’s condition, and you decide.

4

We fix it and run a heated test cycle

We replace the part, run the dryer until it cycles heat on and off, leak-check gas models after any work on the gas valve, and leave our 90-day warranty in writing.

Pricing

How Much Does Dryer Repair Cost in Visalia?

Most dryer repairs cost $100 to $200 nationally, with an average around $150; a motor or drum replacement can reach about $450 (Fixr cost data). These are estimated prices only. For the exact cost of your repair, give us a call at (559) 597-1018.

RepairEstimated range, parts & labor
Door switch$50–$150
Drum rollers$100–$150
Gas igniter$100–$250
Thermostat$100–$260
Drive belt$150–$250
Gas valve coils$150–$300
Heating element$150–$350
Motor$250–$450

Estimated national prices from Fixr cost data, for guidance only. Your exact price depends on the part and model. Call us for an exact quote.

What Changes the Price

  • The failed part. A thermal fuse or door switch costs far less than a motor.
  • Gas or electric. Gas repairs take a little longer because we leak-check after any work on the gas valve.
  • Vent condition. A badly clogged dryer duct adds cleaning time; we’ll show you what we find before we do it.
  • Access. Stacked units in tight closets take longer to pull out and open.

These prices are estimates. Call for your exact price.

Every dryer is different. Call us, tell us gas or electric and what it’s doing, and we’ll give you the exact cost. Our diagnostic visit is $49, and you get the full price in writing before we start.

Should You Repair or Replace Your Dryer?

Repair it if the fix costs less than about half the price of a comparable new dryer. Fixr puts typical dryer life at 8 to 12 years, and many well-kept dryers last longer. Dryers are mechanically simple, so fuses, elements, igniters, belts and rollers are almost always worth fixing.

The harder calls are a failed motor or control board on an older budget model, or a cracked drum. We’ll give you the number and an honest opinion.

Why trust us

Licensed, Registered and Guaranteed

State registration

California requires appliance repair businesses, including dryer repair, to register with the Bureau of Household Goods and Services (BHGS). We’re registered, and you can look us up on the BHGS website before you book.

Gas work

We repair the gas components inside the dryer and leak-check every connection we touch. New gas lines and shutoff valves go to a licensed plumber.

Fully insured

Licensed and fully insured for work in your home.

90-day warranty

Parts and labor, in writing.

No surprise bills

You approve a written price before we start.

4.8

Average rating from 100+ customer reviews on Google.

FAQ

Dryer Repair FAQs for Visalia Homeowners

We’re open 24/7 and can usually reach you the same day. A dryer that’s overheating goes to the front of the line. If we need to order a part, you get its arrival date in writing.

On an electric dryer, the usual causes are a blown thermal fuse, a burned-out heating element, a failed thermostat, or one half of the 240-volt breaker tripped. On a gas dryer, it’s usually the igniter, flame sensor or gas valve coils. A blown fuse often means the vent is clogged, so we check airflow too.

Most often, restricted airflow from a clogged vent, a crushed hose behind the dryer, or a stuck outside flap. Feel the air at the outside vent while the dryer runs; it should be a strong, warm blast. A washer that doesn’t spin out enough water causes the same symptom.

Yes. We repair igniters, flame sensors, gas valve coils and burners on natural gas and propane dryers, and leak-check our work. New gas lines and shutoff valves go to a licensed plumber.

Clean the lint screen every load. Have the full vent run checked about once a year, or sooner if loads start taking longer to dry. Visalia’s dust and the heavy dryer use of tule fog season are good reasons not to wait.

Usually yes. Dryers are simple machines, and fuses, elements, igniters, belts and rollers are inexpensive. A failed motor or board on an older budget model is the main case where replacement can make more sense.

No. Dryer manufacturers specify rigid or UL-listed flexible metal duct. Plastic hose is not approved, and thin foil crushes and traps lint. We can swap it during the visit.

Yes: Tulare, Exeter, Farmersville, Goshen, Ivanhoe and Yettem. See our service areas.

Need help now?

Book Dryer Repair in Visalia Today

Tell us gas or electric, the brand, and what it’s doing, and we’ll give you the earliest arrival time we have in Visalia. A dryer that’s overheating goes first.

  • Same-day & emergency appointments
  • $49 diagnostic, written quote first
  • 90-day parts & labor warranty

Book a dryer repair

Tell us what’s wrong and when suits you. We’ll call you back to confirm your appointment.

Dryer overheating? Call (559) 597-1018 for the fastest help.